condor d.c. power supplies, inc., a subsidiary of sl industries, inc. 805-486-4565 ?(800) 235-5929 fax: (805) 487-8911 http://www.condorpower.com 160, 220 watts multiple output mdt -160 mtc -160 mdt -220 featuring: 9?x 5?x 2.5?package proven low component count design high power densities meets international safety agency requirements high peak currents for motor starting remote sense, thermal protection, and ovp cannot be damaged by no load or low line conditions ac automatic line selection option model pwr output #1 output #2 output #3 mtc-163-0515 160 +5v @ 30a +15v @ 1.5a -12v @ 1.5a telecom mtc series model pwr output #1 output #2 output #3 output #4 mdt-163-0512r 160 +5v @ 25a +12v @ 4/9 a pk +12v @ 1.5a mdt-164-1212r 160 +5v @ 25a +12v @ 4/9 a pk +12v @ 1a -12v @ 1a mdt-164-2412r 160 +5v @ 20a +24v @ 3/6 a pk +12v @ 1a -12v @ 1a mdt-223-0512r 220 +5v @ 30a +12v @ 6/10 a pk 12v @ 2.5a mdt-224-1212r 220 +5v @ 30a +12v @ 6/10 a pk +12v @ 1.5a -12v @ 1.5a mdt-224-2412r 220 +5v @ 25a +24v @ 4/8 a pk +12v @ 1.5a -12v @ 1.5a standard mdt series model pwr output #1 output #2 output #3 mdt-223-1212r 220 +5v @ 10a +12v @ 10/16 a pk -12v @ 1a mass storage mdt-223-1212r these are condor s lower power series. they are ideal for new oem products that are designed for future expansion. outputs start at 160 watts and power needs can go to 350 watts by using the max-350 series without changing the footprint. you?l get up to 30 amps for logic and memory, and peak currents up to 16 amps for motor starting in a package measuring only 9?x 5?x 2.5? other features like high power densi- ties, ac autoline select option, and meet- ing international safety requirements, give design flexibility, low price, and worldwide marketability. check the specifications of these power supplies for your next oem computer- based or telecom product design. *9.05 229.87 for mtx
condor d.c. power supplies, inc., a subsidiary of sl industries, inc. 805-486-4565 ?(800) 235-5929 fax: (805) 487-8911 http://www.condorpower.com function 115 vac 230 vac connector input select short open .110 male fastons or #16 bus jumper tb1- line line 1 tb1- neutral line 2 tb1- safety ground safety ground specifications: all models input ac input: 90-132 vac/180-264 vac, 47 to 63 hz. user selectable. see option ??for automatic line selection. internally fused for 7 a. inrush: cold start ac current is less than 16 a at 115 vac and 32 a at 230 vac. limited by thermistor. holdup time: 16 ms minimum after removal of power, at nominal line, full load. efficiency: 75% typical. brownout protection: holds regulation to 85 vac or 170 vac. output adjustability: main output and output #3 user adjustable ?% minimum. output #4 (output #3 in mtc series) is not adjustable and has ?% initial accuracy. line & load reg: ?% over ac input range and 0 to 100% load change. on mdt series only, output #2 holds ?% total regulation band, including the combined effects of line regulation, load regulation for a load change of ?0% from 60% initial load, and cross regulation due to a load change of ?5% on the 5 v line from 60% initial load. maximum combined currents on outputs #1 and 2 cannot exceed output #1 rating, except for mdt-223-1212r. main +5 v output requires minimum load of 20% for all models. ripple & noise: less than 1% p-p or 100 mv, whichever is greater. remote sense (+5v): compensates for 250 mv total line drop. open sense lead protection. temperature coefficient: 0.02% per degree c. stability: 0.1% over 8 hours after 30 minutes warm-up. transient response (+5v): output voltage returns to within 1% in less than 500 ? for a 50% load change. peak transient does not exceed 5%. overload protection: all outputs are protected against overload and short circuit. automatic recovery upon removal of fault. overvoltage protection (+5v): protects load against power supply induced overvoltage. trip point is factory set so that output voltage cannot exceed 6.8 v. reverse voltage: protected against reverse voltage up to supply current rating. environmental thermal protection: shuts down power supply if overheated. automatic recovery. temperature range: 0 to 50? at full ratings. derate to half power at 70 ?. safety agencies: most models are approved to ul1950; csa 22.2 #234; iec 950 and t?v en60950, class 1 selv., ce 72/23/eec/93/68eec (low voltage directive). conducted rfi: meets fcc part 15, subpart j, class a; en55022 class b; cispr 22 class b. output isolation: isolated from ground 50 vdc. cooling: 30 cfm required to achieve full ratings. mdt-160 models are convection cooled. 160, 220 watts 9 x 5 x 2.5 mdt-160, 220 mtc-160 ac input function mdt-163/223 mdt-164/224 mtc-163 connector output #1 terminal +5 terminal +5 terminal +5 bus bars terminal com terminal com terminal com #6-32screws output #2 tb2-3 (+) tb2-4 (+) tb2-3 (+) barrier strip tb2-4 (rtn) tb2-5 (rtn) tb2-2 (rtn) #6-32 screws output #3 tb2-2 (+) tb2-3(+) tb2-1 (? 3/8?centers tb2-1 (rtn) tb2-2 (rtn) tb2-2 (rtn) output #4 tb2-1 (? tb2-2 (rtn) note: return lines (rtn) are connected to power supply common(com) dc output barrier strip #6-32 screws 3/8?centers function location notes connector terminal + s output #1 sense terminal ?s output #1 sense rtn ac power fail terminal pf reference to (?s) (optional function) status and control #6-32 screws remote sense options: option ?? ac auto-range: automatically selects proper ac line voltage range to enable power operation at either 115 or 230 vac without user intervention. option ?? ac power fail: provides ttl ?? 5 ms before output voltage goes out of regulation band upon loss of ac power. vmebus compatible, provides 48 ma sink current capability. consult factory for other available options. mtc-160 2.6 lbs - 1.2 kgs mdt-160, 220 2.6 lbs - 1.2 kgs dimensions: inches millimeters (l) (n) ( )
|
